Carbohydrates as a Construction Kit and Fuel: Technological Perspectives in Food Science
1. Introduction: Carbohydrates as a Construction Kit and Fuel
For decades, dietary carbohydrates have been primarily viewed through the narrow lens of energy supply. In public discourse, they are often simplified into a binary of "good" and "bad" — complex versus simple, whole grain versus refined sugar. However, from a food science and technology standpoint, this dichotomy barely scratches the surface. Carbohydrates are arguably the most versatile class of biomolecules in the food matrix, functioning not merely as fuel but as sophisticated structural architects.
Unlike fats and proteins, whose primary technological roles are often more predictable, carbohydrates offer a dynamic continuum of functionalities. At one end of the spectrum are small sugars like glucose and fructose, which control sweetness, freezing point depression, and humectancy. At the other end are giant polysaccharides — starches, celluloses, pectins, and gums — whose chains can intertwine, gel, stabilize emulsions, and form edible films. Between these extremes lies a vast chemical playground where heat, enzymes, and physical forces can dramatically alter their fate in food (and consequently in the human digestive process).
This article focuses on the technological manipulation of carbohydrates. We will explore how processing methods — from traditional thermal treatment to modern enzymatic engineering — fundamentally change the molecular architecture of carbohydrates, thereby modifying their textural, structural, and nutritional delivery properties. We will discuss the science of starch gelatinization and retrogradation (Fagioli et al., 2019; Roman & Martinez, 2019), the precision of enzymatic remodeling (van der Maarel & Leemhuis, 2013), the gelation mechanisms of hydrocolloids like pectin and alginate (Chan et al., 2017; Cao et al., 2020), and the emerging applications of carbohydrate-based fat replacers, edible films, and 3D food printing inks (Zhang et al., 2018; Fan et al., 2021; Ishwarya et al., 2021).
A key concept that bridges food technology and nutrition is the modulation of starch bioavailability. While this review avoids clinical recommendations, we will examine the structural strategies — such as physical encapsulation, the formation of resistant starch, and the use of viscous soluble fibers — that alter the rate and extent of starch digestion (Miao & Hamaker, 2021; Zheng et al., 2021). These strategies are not medical interventions but rather examples of how material science can design food with different functional outcomes.
It is crucial to distinguish the food technologist's perspective from that of a clinician. The technologist asks: "How can I modify the structure of this carbohydrate to achieve a desired texture, stability, or digestibility profile?" The answer lies in understanding polysaccharide chemistry — the type of glycosidic bonds (α vs. β), the degree of polymerization, the presence of branching or esterification, and the interaction with water and ions (Swackhamer et al., 2025).
For instance, the difference between a crisp chip and a chewy bread is not just a matter of water content but of starch chain organization. The difference between a high-methoxyl pectin gel (setting with sugar and acid) and a low-methoxyl pectin gel (setting with calcium) is a matter of chemical substitution (Chan et al., 2017). And the difference between a rapidly digestible starch and a slowly digestible one can be engineered by creating dense protein-starch matrices or by inducing specific crystalline structures during cooling (Miao & Hamaker, 2021).
This article is structured as a technological primer. We begin with the effects of thermal processing — the most ancient and widespread form of carbohydrate modification. We then move to fermentation and enzymatic methods, followed by an in-depth look at polysaccharides as texture modifiers (hydrocolloids). Finally, we showcase how these principles are combined to create advanced food structures: fat replacers, edible coatings, 3D-printed foods, and controlled-starch matrices. By the end, the reader will appreciate that a carbohydrate is not a static entity but a dynamic, programmable building block of our food supply.
2. Thermal Processing of Carbohydrates: More Than Just Cooking
When a carbohydrate-rich food is heated, a cascade of molecular events unfolds. Water molecules penetrate starch granules, hydrogen bonds break, crystalline structures melt, and polymer chains become mobile. This is not merely "cooking" — it is a precise physical transformation that dictates whether a sauce thickens, a bread develops a crust, or a potato becomes fluffy.
Thermal processing is the most fundamental tool for modifying carbohydrate functionality. It can render raw, indigestible starches into a digestible form, or, through controlled cooling, convert a fraction of them back into enzyme-resistant structures (Roman & Martinez, 2019). Understanding these transformations is essential for any food technologist aiming to design texture, stability, and nutritional delivery.
2.1. Starch Gelatinization: The Swelling and Melting of Granules
Native starch exists as semi-crystalline granules. When heated in the presence of excess water (typically >60% moisture), the granules absorb water, swell, and eventually lose their crystalline order. This irreversible process is called gelatinization (Miao & Hamaker, 2021). During gelatinization, amylose leaches out of the granules, and the system transforms from a granular suspension into a viscous paste.
The temperature at which gelatinization begins (onset temperature, \(To\)) depends on the starch source, the amylose-to-amylopectin ratio, and the presence of co-solutes such as sugars or salts. For most cereal starches, gelatinization occurs between 60 and 75°C (Zheng et al., 2021). The extent of gelatinization critically influences subsequent digestibility: fully gelatinized starch is rapidly hydrolyzed by amylases, while partially gelatinized starch retains some resistance (Roman & Martinez_, 2019).
In baking, starch gelatinization is largely complete in the crumb, where moisture is plentiful. However, in the crust, rapid water evaporation limits gelatinization, leaving a significant fraction of ungelatinized granules — up to 70% in some breads (Roman & Martinez, 2019). This difference between crumb and crust is a striking example of how thermal gradients within a single product create heterogeneous starch structures.
2.2. Retrogradation: The Re-Association of Starch Chains Upon Cooling
Gelatinization is not the end of the story. When a cooked starch paste is cooled, the dispersed amylose and amylopectin chains begin to re-associate through hydrogen bonding. This process, known as retrogradation, leads to the formation of ordered, crystalline-like structures that are more resistant to enzymatic attack (Roman & Martinez, 2019; Miao & Hamaker, 2021).
Retrogradation occurs in two stages. Short-term retrogradation (within hours) is driven primarily by amylose, which forms double helices and precipitates. Long-term retrogradation (over days) involves the outer branches of amylopectin. The resulting structures are classified as resistant starch type 3 (RS3) — a form of dietary fiber that resists digestion in the small intestine (Roman & Martinez, 2019).
Cooling temperatures profoundly affect retrogradation. Storing cooked starch at refrigerator temperatures (4°C) promotes retrogradation, whereas freezing (−20°C) or keeping it warm (>60°C) slows the process. This is why cooked potatoes or rice that have been cooled overnight contain more resistant starch than when freshly cooked ( van der Maarel & Leemhuis, 2013). The food industry exploits this principle in the production of retrograded starch ingredients (e.g., from high-amylose maize) that are marketed as resistant starch additives.
2.3. The Maillard Reaction and Caramelization: Creating Color and Flavor
Participation of inulins and fructooligosaccharides in the Maillard reaction
There are two pathways for carbohydrates to participate in the Maillard reaction: (A) direct participation of the reducing end of fructans; (B) hydrolysis by yeast invertase and inulinase followed by inclusion of the products in the reaction. Jackson et al. (2023), Figure 2. CC BY 4.0
While not strictly affecting starch bioavailability, thermal reactions involving simple sugars are crucial for the sensory quality of foods. Two major pathways exist:
Caramelization occurs when sugars (mainly sucrose, glucose, or fructose) are heated above their melting point (typically >160°C) in the absence of amino compounds. The sugars dehydrate and fragment, producing a complex mixture of volatile compounds (diacetyl, maltol, furans) and brown polymers (caramelans, caramelens). Caramelization is responsible for the characteristic color and toffee-like flavor of caramel candies, cola beverages, and roasted nuts (Jackson et al., 2023).
The Maillard reaction is a non-enzymatic browning reaction between reducing sugars (glucose, fructose, lactose) and amino acids or proteins. It proceeds through a series of complex steps: the formation of a Schiff base, rearrangement to Amadori products, and subsequent fragmentation, dehydration, and polymerization. The Maillard reaction generates hundreds of volatile compounds (pyrazines, furans, thiols) responsible for the savory, roasted, and toasty notes of bread crust, coffee, and grilled meat (Jackson et al., 2023).
Importantly, the Maillard reaction requires reducing sugars. Sucrose, a non-reducing sugar, must first be hydrolyzed to glucose and fructose (e.g., by invertase in yeast-leavened doughs) before it can participate. This has implications for low-GI formulations: replacing sucrose with non-reducing sweeteners may reduce browning, while adding fructose (a highly reactive reducing sugar) accelerates color development (Jackson et al., 2023).
2.4. How Cooking Methods Shape Starch Structure: Boiling, Baking, Extrusion
Microstructure of crumb and crust of bread with the addition of resistant starch
Micrographs of a cross-section of bread containing 20% resistant starch from green banana: (left) crumb – fully gelatinized, (right) crust – isolated ungelatinized granules are visible (indicated by arrows). Magnification 20 µm. Roman & Martinez (2019), Figure 2. CC BY 4.0
Different thermal processes impart distinct structural signatures on starch and other carbohydrates.
Boiling (100°C, excess water) results in complete gelatinization of starch granules, as water is abundant. The granules swell and rupture, releasing amylose. Upon cooling, a firm gel forms due to retrogradation. Boiled potatoes, rice, and pasta typify this behavior.
Baking involves a combination of heat transfer and water evaporation. The interior of a baked product (crumb) reaches 95–100°C and remains moist, allowing full gelatinization. The surface (crust) experiences temperatures above 150°C and rapid moisture loss, which limits gelatinization, promotes Maillard browning, and can even form some resistant starch structures (Roman & Martinez, 2019).
Extrusion is a high-temperature, short-time (HTST) process widely used for breakfast cereals, snacks, and pasta. Starches are subjected to high shear, pressure, and temperatures (120–180°C) at relatively low moisture (12–30%). This causes complete gelatinization, molecular fragmentation, and often, partial degradation of added prebiotic fibers such as inulin and fructooligosaccharides (Jackson et al., 2023). However, extrusion can also be used to create slowly digestible structures if the formulation includes high-amylose starch or specific hydrocolloids (van der Maarel & Leemhuis, 2013).
Extrusion is also a tool for modifying soluble dietary fibers. For example, in the production of extruded breakfast cereals, the addition of long-chain inulin (DP > 10) can increase crispness, although high temperatures and screw speeds (170°C, 170 rpm) can degrade more than 50% of short-chain fructooligosaccharides (Jackson et al., 2023). This highlights the need to match fiber type to processing conditions.
In summary, thermal processing is not a simple on/off switch for carbohydrate digestibility. It is a continuum: from fully gelatinized, rapidly digestible starch to partially retrograded, resistant forms. The technologist's skill lies in choosing the right combination of temperature, water, time, and cooling regime to achieve the desired structural outcome.
3. Fermentation: The Work of Microbes and Enzymes
Beyond heat, living organisms and their molecular tools offer a powerful means to reshape carbohydrates. Fermentation — whether driven by whole microbial communities or isolated enzymes — can modify the length, branching, and solubility of polysaccharides, thereby altering their technological performance and nutritional behavior. This section distinguishes between two complementary approaches: traditional food fermentation (using sourdough, for example) and modern enzymatic engineering (using purified enzymes to create novel starch derivatives).
3.1. Traditional Fermentation: The Example of Sourdough
Sourdough is the oldest biotechnology for leavening and transforming cereal flours. Unlike baker’s yeast alone, sourdough harbors a stable consortium of lactic acid bacteria (LAB) and yeasts. Common LAB species include Lactobacillus sanfranciscensis, L. plantarum, and L. brevis (Ma et al., 2021). During fermentation, these microorganisms produce organic acids (lactic and acetic), lower the pH, and secrete a range of enzymes — including phytases, proteases, and xylanases.
For whole-wheat or whole-grain products, sourdough fermentation offers several technological advantages. It increases the solubility of water-unextractable arabinoxylans (a major hemicellulose in bran) by activating endogenous xylanases, leading to improved dough handling and higher bread volume (Ma et al., 2021). The acidic environment also enhances endogenous wheat protease activity, which partially hydrolyzes gluten proteins. This does not destroy gluten entirely but modifies its viscoelastic properties, making the dough more extensible.
Crucially, sourdough fermentation affects the starch and sugar composition. The yeasts and LAB consume maltose and other sugars, producing carbon dioxide and organic acids. Some heterofermentative LAB (e.g., L. sanfranciscensis) produce mannitol from fructose, contributing to the maintenance of a healthy gut microbiota (Ma et al., 2021). The organic acids also lower the pH, which can accelerate starch retrogradation upon cooling, thereby increasing the formation of resistant starch (RS3).
From a sensory standpoint, sourdough fermentation generates a wide array of volatile aroma compounds — carboxylic acids, esters, alcohols, aldehydes, and ketones — that impart a complex, slightly sour, and fruity profile to bread. These compounds are largely absent in breads leavened only with commercial yeast (Ma et al., 2021). Thus, sourdough acts not only as a leavening agent but also as a natural flavor enhancer and texture modifier.
3.2. Enzymes as Biotechnological Tools
While whole microbes are effective, isolated enzymes provide even finer control over carbohydrate structure. Enzymes are proteins that catalyze specific reactions — hydrolysis, transglycosylation, isomerization — under mild conditions (temperature, pH). In the context of carbohydrates, two broad classes are particularly important: hydrolases (which cleave glycosidic bonds) and transglycosidases (which cleave and re-form bonds).
α-Amylases and Glucoamylases: From Starch to Syrups
The industrial production of glucose syrups, maltodextrins, and high-fructose corn syrup relies on a two-step enzymatic process. First, a heat-stable α-amylase (EC 3.2.1.1) liquefies a 30–35% starch slurry at 90–100°C, randomly hydrolyzing α-1,4 linkages and producing a low-viscosity mixture of oligosaccharides. Second, glucoamylase (EC 3.2.1.3) and pullulanase (EC 3.2.1.41) saccharify the liquefied starch at 60°C, cleaving both α-1,4 and α-1,6 bonds to yield over 97% glucose. This glucose can then be isomerized to fructose by glucose isomerase (van der Maarel & Leemhuis, 2013).
These processes are among the largest industrial enzyme applications. The resulting sweeteners are used in soft drinks, confectionery, baked goods, and as fermentation feedstocks for bioethanol. Importantly, the molecular weight and degree of polymerization of the final product can be controlled by adjusting enzyme dosage, reaction time, and temperature.
Alpha-Glucanotransferases: Remodeling Without Destruction
Unlike amylases, which simply hydrolyze starch, alpha-glucanotransferases (AGTases) break a glycosidic bond and transfer the cleaved fragment to a new acceptor molecule, forming a new bond. This disproportionation reaction allows them to “rewire” the starch molecule without net loss of sugar units. AGTases belong to glycoside hydrolase families 13, 57, and 77 (van der Maarel & Leemhuis, 2013).
Three types of AGTases are of technological interest:
- 4-α-Glucanotransferase (4αGT, EC 2.4.1.25) transfers α-1,4-linked glucan chains to the non-reducing end of another glucan, effectively shuffling chain segments. When incubated with starch, 4αGT produces a thermoreversible gel (marketed as Etenia™) that mimics gelatin. This gel melts upon heating and re-forms upon cooling, making it a plant-based alternative to animal gelatin for confectionery and low-fat products (van der Maarel & Leemhuis, 2013).
- Cyclodextrin glucanotransferase (CGTase, EC 2.4.1.19) predominantly catalyzes intramolecular transglycosylation, producing cyclic oligosaccharides (cyclodextrins) of 6, 7, or 8 glucose units. Cyclodextrins form inclusion complexes with hydrophobic molecules, enabling the solubilization of lipophilic compounds, the stabilization of flavors, and the removal of cholesterol from foods (van der Maarel & Leemhuis, 2013).
- Branching enzyme (BE, EC 2.4.1.18) cleaves an α-1,4 linkage and transfers the cut chain to a 6‑hydroxyl of a nearby glucose, creating an α-1,6 branch. By introducing additional branch points, BE converts amylose into highly branched, water-soluble α-glucans that resist retrogradation and exhibit slower amylase digestion. Commercial products such as Branchzyme™ (from Rhodothermus obamensis) are used to produce slowly digestible starches (van der Maarel & Leemhuis, 2013).
Combining branching enzyme with a debranching enzyme (e.g., pullulanase) followed by crystallization yields a new type of resistant starch (Promitor™), which has been shown to lower glycemic and insulin responses in healthy volunteers (van der Maarel & Leemhuis, 2013). This is a clear example of how enzyme-catalyzed structure engineering can produce a food ingredient with distinct nutritional properties.
Enzymatic Modification of Non-Starch Polysaccharides
Enzymes also target dietary fibers. For arabinoxylans (AX), xylanases (endoxylanases) can hydrolyze the xylan backbone, releasing arabinoxylo-oligosaccharides (AXOS) with prebiotic potential. Similarly, endopolygalacturonase and pectin methylesterase (PME) modify pectin’s degree and pattern of methoxylation, influencing its calcium sensitivity and gelling behavior (Chan et al., 2017; Cao et al., 2020).
The pattern of methyl-esterification (described by the degree of blockiness, DB, and absolute degree of blockiness, DBabs) critically affects pectin gelation. Enzymatic de-esterification using fungal PME produces a random pattern, while plant PME often produces a blockwise pattern. Blockwise de-esterified pectins form stronger calcium gels because they have longer contiguous stretches of non-methylated galacturonic acid that can participate in egg-box junction zones (Chan et al., 2017).
In summary, fermentation and enzymatic processing offer a versatile toolkit for carbohydrate engineers. Traditional fermentation modifies the entire food matrix — bran, starch, proteins, and flavor precursors — while isolated enzymes enable precision editing of polysaccharide structure. Both approaches are essential for producing the wide range of carbohydrate-based ingredients and foods available today.
4. Polysaccharides as Food Structure Builders
While starches are primarily energy reserves, a diverse family of non-starch polysaccharides — often called hydrocolloids or gums — serve as structure builders. These molecules are not digested by human enzymes; instead, they hydrate, swell, and interact with water, ions, and other food components to create viscosity, stabilize emulsions, and form gels. From the creamy texture of yogurt to the spreadability of jam, hydrocolloids are ubiquitous in modern food systems.
This section explores the structure–function relationships of major hydrocolloids, their gelation mechanisms, and their role in modifying the rheology and texture of food products.
4.1. What Are Hydrocolloids and Why Are They Used?
Hydrocolloids are water-soluble polysaccharides (and some proteins) that disperse in water to produce thickening, gelling, or stabilizing effects. They are added to foods for multiple purposes: to control rheology (flow behavior), improve mouthfeel, retard ice crystal growth in frozen desserts, prevent syneresis (water separation), and extend shelf life (Salehi, 2020).
Common hydrocolloids include xanthan gum, guar gum, locust bean gum, carrageenan, alginate, pectin, carboxymethyl cellulose (CMC), and methylcellulose (MC) ( Salehi, 2020). Their functional properties are determined by molecular weight, monomer composition, glycosidic linkages, degree and pattern of substitution (e.g., methoxylation, acetylation), and chain conformation.
A key distinction is between thickeners (which increase viscosity without forming true gels) and gelling agents (which form a three-dimensional network capable of immobilizing water). However, many hydrocolloids can act as both, depending on concentration and conditions.
4.2. Gelation Mechanisms: Pectin and Alginate as Paradigms
Two of the most studied gel-forming polysaccharides are pectin (from plant cell walls) and alginate (from brown seaweeds). Both are polyuronates — polymers containing uronic acid residues. Their gelation is classically described by the egg-box model, though important differences exist.
High-Methoxy Pectin (HMP): Gelling with Sugar and Acid
Pectin is classified by its degree of methylation (DM), the percentage of galacturonic acid residues esterified with methanol. High-methoxy pectin (DM > 50%) gels under specific conditions: low pH (2.5–3.5) and high soluble solids (typically 55–75% sucrose) (Chan et al., 2017).
The mechanism involves two synergistic forces. Low pH protonates the free carboxyl groups, reducing electrostatic repulsion between pectin chains. High sugar concentration lowers water activity (dehydration), promoting chain–chain interactions. The actual junction zones are stabilized by hydrogen bonds between undissociated carboxyl groups and secondary alcohols, as well as hydrophobic interactions between methyl ester groups (Chan et al., 2017).
HMP gels are thermoreversible: they melt upon heating and re-set on cooling, though some hysteresis may occur. The gelation rate depends on the pattern of methyl groups; pectins with a blockwise distribution (higher degree of blockiness, DB) gel faster and form stronger gels than those with random distribution (Chan et al., 2017).
Low-Methoxy Pectin (LMP) and Alginate: Ionic Gelation (Egg-Box Model)
Low-methoxy pectin (DM < 50%) and alginate gel by a different mechanism: ionotropic gelation with divalent cations, typically calcium (Ca2+). This is described by the egg-box model, first proposed for alginate and later extended to pectin (Cao et al., 2020).
In the egg-box model, two antiparallel polyuronate chains form a dimeric junction zone. Calcium ions are coordinated with the carboxylate groups (COO-) and hydroxyl oxygens of the sugar residues. For stable junction zones, contiguous sequences of non-methoxylated galacturonic acid (in pectin) or guluronic acid (G-blocks in alginate) are required — a minimum of 6–8 consecutive units for alginate and 6–20 for pectin (Cao et al., 2020).
The gelation proceeds in three steps (for alginate): monocomplexation (Ca2+ binds to a single chain), dimerization (two chains pair via Ca2+ bridges), and lateral association (dimers aggregate to form multimers). For pectin, lateral association is less pronounced; the dimers grow more in a “dotting” rather than a “zippering” mode (Cao et al., 2020). This difference arises from the branched structure of pectin (with neutral sugar side chains) versus the linear structure of alginate.
Critical factors influencing LMP/alginate gelation include:
- Concentration of Ca2+: described by the R value (2Ca2+/COO-). For alginate, optimal stiffness occurs around R = 0.25; excess Ca2+ causes syneresis (water expulsion) (Cao et al., 2020).
- Polymer concentration: higher concentrations produce denser, stronger gels.
- pH: for LMP, pH must be above the pKa (~3.5) to ensure carboxyl groups are ionized. Below this, acid-induced gelation via hydrogen bonds predominates, but such gels are weaker (Cao et al., 2020).
- Temperature: Ca-pectin gels are partially thermoreversible (melting at ~50°C), whereas Ca-alginate gels are thermally irreversible up to 100°C (Cao et al., 2020).
Amidated Low-Methoxy Pectin (ALMP)
Amidated pectin is produced by reacting HMP with ammonia, which converts some methyl esters to primary amide groups. ALMP has two advantages: it requires less calcium for gelation and is less prone to syneresis. Moreover, ALMP can form gels by acidification alone (without calcium), and these acid gels are thermally reversible — they melt on heating and re-gel on cooling (Chan et al., 2017). This property is unique among pectins and is exploited in certain dessert applications.
4.3. Other Common Hydrocolloids: Xanthan, Guar, CMC, and Beyond
Beyond pectin and alginate, several other hydrocolloids are widely used as thickeners and stabilizers.
Xanthan gum (produced by Xanthomonas campestris) has a cellulose backbone with trisaccharide side chains. It exhibits high viscosity at low concentrations, is pseudoplastic (shear-thinning), and is stable over a wide pH range and temperature. Xanthan does not gel alone but can form synergistic gels with locust bean gum or konjac glucomannan (Salehi, 2020).
Guar gum (from Cyamopsis tetragonolobus seeds) is a galactomannan. It is highly water-soluble and acts primarily as a thickener. Guar has a higher molecular weight and viscosity than locust bean gum at the same concentration (Salehi, 2020).
Locust bean gum (LBG) (from carob tree seeds) is also a galactomannan but with fewer galactose branches. It does not dissolve completely in cold water; heat is required. LBG is notable for its synergistic interaction with xanthan or carrageenan to form elastic gels (Salehi, 2020).
Carboxymethyl cellulose (CMC) is a chemically modified cellulose. It is anionic and water-soluble, forming clear, viscous solutions. CMC is used extensively in gluten-free baking to mimic the viscoelastic properties of gluten (Salehi, 2020).
Methylcellulose (MC) and hydroxypropyl methylcellulose (HPMC) are cellulose ethers. They exhibit thermal gelation: they dissolve in cold water but form a gel when heated, then revert to solution upon cooling. This unique property is exploited in fried foods and as a fat barrier in baked goods (Salehi, 2020).
4.4. Emerging Hydrocolloids from Seed Gums
Extraction of basil seed gum for use in sponge cake
A process for obtaining basil seed gum (Ocimum basilicum) by cold-water extraction followed by ethanol precipitation and drying. The resulting gum is added to dough to improve texture and moisture. Salehi (2020), Figure 1. CC BY 4.0
In addition to established commercial gums, there is growing interest in novel hydrocolloids from underutilized seeds. These offer clean-label appeal and comparable functionality.
Wild sage seed gum (Salvia macrosiphon): This gum produces pseudoplastic solutions with high viscosity. In cake formulations, addition of 1% (flour basis) increased cake volume and moisture while decreasing density (Salehi, 2020).
Basil seed gum (Ocimum basilicum): Extracted by cold water, basil seed gum exhibits high water-holding capacity. At 0.5% (flour basis), it improved sponge cake quality and retarded staling (Salehi, 2020).
Balangu seed gum (Lallemantia royleana): This gum increased moisture and specific volume in sorghum gluten-free bread at 0.5% substitution, while reducing crumb firmness (Salehi, 2020).
Cress seed gum (Lepidium sativum): When combined with guar gum (0.3% each), cress seed gum improved dough rheology and increased bread stability (Salehi, 2020).
These novel gums are often more effective at lower concentrations than traditional gums, providing opportunities for cost reduction and label simplification. However, their extraction and purification need to be optimized for industrial scale-up.
4.5. Hydrocolloids as Fat Replacers and Texturizers
One of the most significant applications of hydrocolloids is in reduced-fat products. By forming microgels or viscous dispersions, polysaccharides can mimic the mouthfeel and lubricity of fat. For example:
Pectin microgels (low-methoxyl pectin cross-linked with calcium) have been used as fat mimetics in mayonnaise. The microgel particles have a size and deformability similar to fat droplets, contributing to creaminess without the calories (Ishwarya et al., 2021).
Inulin, a fructan with a degree of polymerization >10, forms fat-like gels at concentrations above 20% (w/w). In ice cream, replacing fat with 4–5% long-chain inulin (DP > 23) produced sensory scores comparable to full-fat controls (Jackson et al., 2023). In spreadable cheese, inulin improved mouthfeel and spreadability while reducing hardness.
Konjac glucomannan (KGM) and xanthan gum are used to produce fluid gels that act as fat replacers in sauces and dressings.
From a textural standpoint, hydrocolloids also modify the pasting properties of starch. Adding guar gum, CMC, or xanthan to starch suspensions increases peak viscosity and final viscosity, while reducing pasting temperature. The effect depends on the hydrocolloid’s charge, molecular weight, and compatibility with amylose (Zheng et al., 2021). Anionic gums (CMC, xanthan) tend to delay starch gelatinization due to electrostatic repulsion, whereas neutral gums (guar, KGM) promote gelatinization.
In summary, hydrocolloids are indispensable tools for food technologists. Their ability to thicken, gel, stabilize, and mimic fats allows the creation of products with desirable textures and extended shelf lives. Understanding the molecular basis of their action — from the egg-box model of alginate to the synergistic networks of xanthan-LBG — is essential for rational formulation design.
5. Engineering “Smart” Carbohydrate Structures for Novel Food Properties
Beyond traditional thickening and gelling, the principles of carbohydrate science are now being applied to create entirely new food structures. These “smart” structures go beyond simply holding water or providing viscosity; they are designed to replace fat, form edible packaging, serve as inks for 3D printing, and modulate starch digestion in a controlled manner. This section highlights four cutting-edge applications where carbohydrate engineering meets food innovation.
5.1. Carbohydrate-Based Fat Replacers
Extraction of pectin from citrus canning wastewater
A flow chart showing the extraction of pectin from wastewater generated during the chemical treatment of citrus fruit membranes during canning. Pectin is used as a fat substitute in ice cream. Zhang et al. (2018), Figure 5. CC BY 4.0
Reducing fat without compromising sensory quality is a major challenge. Fat contributes to creaminess, lubricity, flavor release, and satiety. Carbohydrate-based fat replacers aim to mimic these properties by forming particles or gels with similar rheological behavior to fat droplets.
Mechanism of action. The key is to create microgel particles that are soft, deformable, and of a similar size (typically 1–10 μm) to emulsified fat globules. Low-methoxyl pectin (LMP) cross-linked with calcium ions is an ideal candidate. The resulting “pectin microgel” has a viscoelastic texture that, when sheared in the mouth, produces a creamy sensation ( Ishwarya et al., 2021).
Example: low-fat mayonnaise. In a study by Liu, Xu, and Guo (2007), three pectin-based fat mimetics were tested in mayonnaise: a microparticulate pectin gel (LfP1), a weak pectin gel (LfP2), and a microparticulated whey protein–LMP composite (LfW). At 50% fat replacement, the weak pectin gel (LfP2) produced a structure most similar to full-fat mayonnaise, with lower calories but comparable texture. The mechanism involved the entanglement of oil droplets within the pectin network, creating a solid-like resistance to deformation.
Example: low-fat ice cream. Pectin recovered from citrus canning wastewater was used as a fat replacer in ice cream ( Zhang et al., 2018 ). Replacing 45% of the cream (from 15% down to 8.25%) with 0.72% pectin (w/w) produced a low-fat ice cream with no significant differences in appearance, flavor, or taste compared to the full-fat control. The pectin increased viscosity, overrun (air incorporation), and hardness, while decreasing meltdown rate. Dynamic rheology showed that pectin-containing ice creams had higher storage moduli (G′) and behaved as physical gels, whereas the control transitioned from elastic to viscous behavior at higher frequencies.
Other fat replacers. Inulin (DP > 23), konjac glucomannan, and oat β-glucan are also used as fat mimetics. In cakes, pectin hydrogels replaced up to 50% of margarine without significant loss of sensory quality ( Ishwarya et al., 2021 ). In spreadable cheese, inulin improved spreadability and reduced adhesiveness.
5.2. Edible Films and Coatings from Polysaccharides
The search for sustainable, biodegradable packaging alternatives has driven research into edible films based on polysaccharides. These films can reduce moisture loss, retard oxidation, and even carry antimicrobial or antioxidant compounds.
Why polysaccharides? Polysaccharides like pectin, alginate, xanthan gum, and cellulose derivatives are biocompatible, biodegradable, and form cohesive films. However, pure polysaccharide films often have poor water barrier properties due to their hydrophilicity. This is overcome by blending with other biopolymers (e.g., proteins, lipids) or by cross-linking.
Example: pectin–sodium alginate–xanthan (PAX) composite film. Fan et al. (2021) developed a novel edible film from pectin (6 g/L), sodium alginate (5 g/L), and xanthan gum (optimized at 4 g/L), with glycerol as plasticizer and CaCl2 as cross-linker. The optimized PAX₀ film had a tensile strength of 29.65 MPa (exceeding polyethylene and polyvinyl chloride preservative films) and an elongation at break of 19.02%. Its water vapor transmission rate was 18.12 × 10-1¹ g/(m²·s·Pa), which is low enough to inhibit water transfer between food and surroundings.
When applied as a coating on fresh-cut potatoes, PAX₀ coating (with or without CaCl2 spray) reduced weight loss from 17–26% (control) to only 2.7–5.2% after 8 days of storage. The coating also prevented browning by acting as an oxygen barrier. This demonstrates the dual function of edible films: protection and preservation.
Functionalization. Pectin–cellulose composite films loaded with tea polyphenols (antioxidants) and cinnamaldehyde (antimicrobial) showed clear inhibition zones against Escherichia coli, C. albicans, and S. aureus ( Ishwarya et al., 2021 ). Such active packaging can extend shelf life while being fully edible.
5.3. 3D Food Printing with Pectin Inks
3D food printing (additive manufacturing) allows the creation of personalized foods with complex shapes, textures, and nutritional profiles. A major bottleneck is the limited availability of “printable” food materials. Low-methoxyl pectin (LMP) has emerged as a promising food ink.
Requirements for printability. A printable material must have: (i) sufficient viscosity to be extruded smoothly, (ii) shear-thinning behavior (viscosity decreases under shear during extrusion but recovers after deposition), and (iii) rapid solidification to retain the printed shape. LMP gels meet these criteria when combined with calcium ions and sugar syrup.
Controlling cross-linking. The stoichiometric ratio R = 2Ca2+/COO- is critical. Partial cross-linking (R = 0.2–0.5) during printing allows the ink to flow, while complete gelation occurs post-printing (e.g., by incubation in CaCl2 solution). Higher pectin concentrations (15–35 g/L) yield firmer products ( Ishwarya et al., 2021 ).
Coaxial extrusion. A recent innovation is the coaxial extrusion print-head, where pectin solution and CaCl2 solution are delivered simultaneously through inner and outer nozzles. This induces gelation during printing, eliminating the need for post-print incubation. The resulting objects have controllable Young’s moduli and Ca2+ distribution ( Ishwarya et al., 2021 ).
Example: 3D-printed fruit-based snacks. Derossi et al. (2018) developed a printable formulation containing 70% banana, white beans, dried milk, lemon juice, mushrooms, and ascorbic acid, plus 30% pectin solution (11% pectin). The pectin prevented phase separation and provided the necessary viscosity, enabling the production of nutritionally customized snacks for children.
5.4. Controlling Starch Bioavailability through Matrix Design
One of the most active areas of carbohydrate research is the modulation of starch digestion rate and extent. This is not about medical advice but about understanding how food structure — at the cellular, molecular, and macroscopic levels — can influence enzyme access.
Starch nutritional fractions. Starch is classified into rapidly digestible starch (RDS, digested within 20 min), slowly digestible starch (SDS, 20–120 min), and resistant starch (RS, undigested in the small intestine) ( Miao & Hamaker, 2021 ). SDS and RS are associated with lower postprandial glucose responses, but here we focus on the structural strategies to increase them.
Physical barriers. Intact cell walls act as a barrier to α-amylase. In legumes and some cereals, starch granules are enclosed within cell walls that survive cooking. Coarse milling (particle size > 200 μm) preserves some of this barrier, reducing starch digestibility compared to fine milling (< 50 μm) ( Miao & Hamaker, 2021 ).
Protein–starch matrices. In pasta, a continuous gluten network entraps starch granules, slowing enzyme diffusion. Similarly, in sorghum porridge, protein–phenolic interactions create a web-like network around gelatinized starch. This is why cooked sorghum has lower digestibility than maize or wheat ( Miao & Hamaker, 2021 ).
Encapsulation by polysaccharides. Starch can be microencapsulated within alginate or pectin gels. These starch-entrapped microspheres (diameter ~100–200 μm) are digested slowly because the gel matrix restricts enzyme access. Remarkably, such encapsulated starch ferments slowly in the colon, producing unusually high levels of butyrate — a short-chain fatty acid with multiple health benefits ( Miao & Hamaker, 2021 ).
Effect of soluble viscous fibers. Adding viscous soluble dietary fibers (VSDFs) such as konjac glucomannan (KGM), xanthan gum (XG), carboxymethyl cellulose (CMC), or high-methoxyl pectin (HMP) to starch systems increases viscosity, reduces pasting temperature, and decreases gelatinization enthalpy. More importantly, these fibers inhibit starch digestibility and significantly increase resistant starch content. Zheng et al. (2021) compared four VSDFs in rice starch and found that KGM had the most pronounced effect (highest RS increase), while CMC had the least. XG improved paste stability without greatly affecting viscosity, making it a good stabilizer.
Interaction with polyphenols. Polyphenols (e.g., tea polyphenols, chlorogenic acid) can bind to starch via non-covalent interactions, forming V-type inclusion complexes. These complexes are more resistant to α-amylase and also inhibit the enzyme directly ( Miao & Hamaker, 2021 ).
Whole-grain structure as a natural design. The botanical structure of whole grains — with bran layers, protein matrix, and intact cell walls — is a natural example of a slowly digestible system. Processing that preserves this structure (e.g., rolled oats, coarse bulgur) results in lower starch digestibility than processing that disrupts it (e.g., fine milling, extrusion puffing). This is a key principle: the physical form of the grain matters as much as its composition ( Miao & Hamaker, 2021 ).
In summary, “smart” carbohydrate structures are not science fiction — they are already in products on supermarket shelves. Fat-replaced ice cream, edible fruit coatings, 3D-printed snacks, and slowly digestible pasta are all examples of how a deep understanding of polysaccharide chemistry enables the creation of foods with novel, desirable properties. The next section will discuss how these principles are combined in industrial practice and future trends.
6. Conclusion: From Laboratory to Food Industry
The journey of a carbohydrate from a raw agricultural commodity to a component of a formulated food product is a story of molecular transformation. Heat, enzymes, and physical forces reshape these polymers, creating the textures, stabilities, and nutritional behaviors that define modern foods. This review has traversed the technological landscape of carbohydrates, from the kitchen-scale processes of gelatinization and retrogradation to the industrial precision of enzymatic remodeling and the emerging frontiers of 3D food printing and edible films.
6.1. Key Principles Revisited
Several unifying themes emerge from the diverse topics covered.
Structure dictates function. Whether it is the degree of polymerization of inulin determining its fat-mimicking ability (Jackson et al., 2023), the pattern of methoxylation on pectin dictating its calcium sensitivity (Chan et al., 2017), or the presence of α-1,6 branches in amylopectin slowing amylolysis (Miao & Hamaker, 2021), the detailed chemical architecture of a carbohydrate directly controls its technological and nutritional performance. This principle underscores the need for precise characterization — monosaccharide composition, molecular weight distribution, and linkage profile — as proposed by Swackhamer et al. (2025) for the standardization of prebiotic fibers.
Processing is a design tool. Thermal treatment is not merely a means to cook food; it is a controllable variable to achieve specific structural outcomes. Partial gelatinization, controlled retrogradation, and extrusion at defined moisture and temperature profiles allow the creation of starches with tailored digestibility (Roman & Martinez, 2019; van der Maarel & Leemhuis, 2013). Likewise, fermentation with sourdough or specific enzyme cocktails can remodel the food matrix, improving texture, flavor, and even the stability of bioactive compounds (Ma et al., 2021).
Hydrocolloids are multifunctional. Polysaccharides like pectin, alginate, xanthan, and guar are not mere thickeners. They form gels (via the egg-box model or hydrophobic interactions), stabilize emulsions, replace fat, and create edible films. Their versatility arises from their ability to interact with water, ions, and other biopolymers through hydrogen bonding, electrostatic forces, and hydrophobic effects (Salehi, 2020; Cao et al., 2020).
“Smart” structures require integrated knowledge. The development of low-fat ice cream, edible coatings, 3D-printed food inks, and slowly digestible pasta does not rely on a single technique. It combines knowledge of polysaccharide chemistry, rheology, processing engineering, and nutrition science. For instance, creating a starch-entrapped alginate microsphere that resists amylolysis requires understanding both alginate gelation (egg-box mechanism) and starch retrogradation (Miao & Hamaker, 2021).
6.2. Industrial Relevance and Practical Considerations
Translating laboratory findings to industrial production involves several practical challenges.
Standardization. As Swackhamer et al. (2025) argue, the lack of standardized characterization methods for dietary fibers hinders reproducibility and regulatory acceptance. They propose a stepwise approach: first, monosaccharide composition; second, degree of polymerization (molecular size); third, linkage composition. Adopting such standards would allow manufacturers to produce consistent ingredients and researchers to compare results across studies.
Sensory quality. The addition of resistant starch, legume flours, or hydrocolloids often alters the color, flavor, and texture of baked goods. For example, high levels of resistant starch (above 20%) can reduce bread volume and increase hardness (Roman & Martinez, 2019). However, careful formulation — using a blend of fiber types, adjusting water content, or adding emulsifiers — can mitigate these effects. The Australian GI Symbol program demonstrates that front-of-pack labeling, combined with nutrient criteria, can guide consumers toward healthier choices without compromising taste (Augustin et al., 2015).
Scalability. Enzymatic processes such as those using branching enzyme or 4α-glucanotransferase have been scaled up for commercial production of ingredients like Etenia™ (thermoreversible starch gel) and Promitor™ (resistant starch) (van der Maarel & Leemhuis, 2013). However, novel sources such as wild sage seed gum or balangu seed gum remain at laboratory scale; their extraction, purification, and cost-effectiveness need optimization (Salehi, 2020).
Clean label and sustainability. Consumers increasingly demand natural ingredients and minimal chemical processing. This favors the use of native starches, enzymatically modified fibers, and plant-derived hydrocolloids over chemically modified versions (e.g., RS4). Additionally, extracting pectin from citrus canning wastewater (Zhang et al., 2018) or using legume flours as protein and fiber sources (Binou et al., 2022) aligns with circular economy principles.
6.3. Future Directions
Several trends are likely to shape the next decade of carbohydrate technology.
Personalized nutrition. The ability to print 3D foods with customized shapes and nutrient profiles opens the door to individualized products for specific age groups, activity levels, or metabolic needs (Ishwarya et al., 2021). Pectin-based inks, with their tunable texture and calcium cross-linking, are particularly promising.
Microbiome-targeted fibers. As understanding of the gut microbiome deepens, fibers will be designed not just for physical properties but for selective fermentation by beneficial bacteria. The linkage composition of a fiber determines which bacterial taxa can utilize it (Swackhamer et al., 2025). This could lead to “precision prebiotics” that promote specific microbial metabolites (e.g., butyrate) without broad, unpredictable shifts.
Enzyme engineering. Directed evolution and protein engineering are creating new α-glucanotransferases with tailored specificity, thermostability, and product profiles. These enzymes could generate novel cyclic glucans, highly branched starches, or resistant maltodextrins with improved functionality (van der Maarel & Leemhuis, 2013).
Hybrid systems. Combining polysaccharides with proteins, lipids, or polyphenols can produce synergistic effects. For example, ternary complexes of starch–fatty acid–protein form nanoscale delivery systems for lipophilic bioactives while also modulating starch digestion (Miao & Hamaker, 2021). Edible films that incorporate both antimicrobial agents and oxygen barriers are another example of hybrid functionality.
Artificial intelligence and modeling. Machine learning models are beginning to predict the pasting behavior of starch–hydrocolloid mixtures, the gel strength of pectin–calcium systems, or the printability of food inks based on formulation parameters. Such tools can accelerate formulation development and reduce trial-and-error experimentation.
6.4. A Final Word
Carbohydrates are far more than simple energy sources. They are a testament to the power of molecular design in food science. By understanding how heat, enzymes, and physical forces alter their structure, we can create foods that are not only safe and tasty but also structurally innovative and nutritionally thoughtful. This technological perspective — grounded in chemistry, physics, and biology — is essential for addressing the global challenges of sustainable food production, reduced food waste, and improved public health through diet.
The journey from the laboratory to the food industry is long, but the tools and principles outlined in this review provide a solid foundation. As research continues to unravel the complexities of polysaccharide behavior, and as processing technologies advance, the carbohydrate will remain a central, dynamic, and programmable building block of our food supply.
References
- Augustin, L.S., Kendall, C.W.C., Jenkins, D.J.A., Willett, W.C., Astrup, A., Barclay, A.W., … Poli, A. (2015). ‘Glycemic index, glycemic load and glycemic response: An International Scientific Consensus Summit from the International Carbohydrate Quality Consortium (ICQC)’. Nutrition, Metabolism and Cardiovascular Diseases, 25(9), 795–815. DOI: 10.1016/j.numecd.2015.05.005 PubMed
- Binou, P., Yanni, A.E., & Karathanos, V.T. (2022). ‘Physical properties, sensory acceptance, postprandial glycemic response, and satiety of cereal based foods enriched with legume flours: a review’. Critical Reviews in Food Science and Nutrition, 62(2), 1–19. DOI: 10.1080/10408398.2020.1858020 PubMed
- Cao, L., Lu, W., Mata, A., Nishinari, K., & Fang, Y. (2020). ‘Egg-box model-based gelation of alginate and pectin: A review’. Carbohydrate Polymers, 242, 116389. DOI: 10.1016/j.carbpol.2020.116389 PubMed
- Chan, S.Y., Choo, W.S., Young, D.J., & Loh, X.J. (2017). ‘Pectin as a Rheology Modifier: Origin, Structure, Commercial Production and Rheology’. Carbohydrate Polymers, 161, 118–139. DOI: 10.1016/j.carbpol.2016.12.033 PubMed
- Fagioli, L., Pavoni, L., Logrippo, S., Pelucchini, C., Rampoldi, L., Cespi, M., Bonacucina, G., & Casettari, L. (2019). ‘Linear Viscoelastic Properties of Selected Polysaccharide Gums as Function of Concentration, pH, and Temperature’. Journal of Food Science, 2019 Jan, 84(1):65-72. DOI: 10.1111/1750-3841.14407 PubMed
- Fan, Y., Yang, J., Duan, A., & Li, X. (2021). ‘Pectin/sodium alginate/xanthan gum edible composite films as the fresh-cut package’. International Journal of Biological Macromolecules, 187, 1–7. DOI: 10.1016/j.ijbiomac.2021.04.111 PubMed
- Ishwarya, S.P., Sandhya, R., & Nisha, P. (2021). ‘Advances and prospects in the food applications of pectin hydrogels’. Critical Reviews in Food Science and Nutrition, 62(16), 4391–4414. DOI: 10.1080/10408398.2021.1875394 PubMed
- Jackson, P.P.J., Wijeyeseera, A., & Rastall, R.A. (2023). ‘Inulin-type fructans and short-chain fructooligosaccharides-their role within the food industry as fat and sugar replacers and texture modifiers-what needs to be considered!’. Food Science & Nutrition, 11, 17–38. DOI: 10.1002/fsn3.3040 PubMed
- Ma, S., Wang, Z., Guo, X., Wang, F., Huang, J., Sun, B., & Wang, X. (2021). ‘Sourdough improves the quality of whole-wheat flour products: Mechanisms and challenges-A review’. Food Chemistry, 360, 130038. DOI: 10.1016/j.foodchem.2021.130038 PubMed
- Marriott, B.P., Birt, D.F., Stallings, V.A., & Yates, A.A. (Eds.) (2020). Present Knowledge in Nutrition, Volume 1: Basic Nutrition and Metabolism. 11th ed. Academic Press. ISBN: 978-0-323-66162-1
- Miao, M., & Hamaker, B.R. (2021). ‘Food Matrix Effects for Modulating Starch Bioavailability’. Annual Review of Food Science and Technology, 12, 169–191. DOI: 10.1146/annurev-food-070620-013937 PubMed
- Roman, L., & Martinez, M.M. (2019). ‘Structural Basis of Resistant Starch (RS) in Bread: Natural and Commercial Alternatives’. Foods, 8(7), 267. DOI: 10.3390/foods8070267 PubMed
- Sagili, V.S., Chakrabarti, P., Jayanty, S., Kardile, H., & Sathuvalli, V. (2022). ‘The Glycemic Index and Human Health with an Emphasis on Potatoes’. Foods, 11, 2302. DOI: 10.3390/foods11152302 PubMed
- Salehi, F. (2020). ‘Effect of common and new gums on the quality, physical, and textural properties of bakery products: A review’. Journal of Texture Studies, 51, 1–10. DOI: 10.1111/jtxs.12482 PubMed
- Swackhamer, C., Jang, S., Park, B.-R., Hamaker, B.R., & Jung, S.K. (2025). ‘Structure-based standardization of prebiotic soluble dietary fibers based on monosaccharide composition, degree of polymerization, and linkage composition’. Carbohydrate Polymers, 352, 123949. DOI: 10.1016/j.carbpol.2025.123949 PubMed
- van der Maarel, M.J.E.C., & Leemhuis, H. (2013). ‘Starch modification with microbial alpha-glucanotransferase enzymes’. Carbohydrate Polymers, 93, 1–6. DOI: 10.1016/j.carbpol.2012.01.065 PubMed
- Zhang, H., Chen, J., Li, J., Wei, C., Ye, X., & Shi, J. (2018). ‘Pectin from citrus canning wastewater as a fat replacer in ice cream’. Molecules, 23, 925. (без DOI)
- Zheng, J., Huang, S., Zhao, R., Wang, N., Kan, J., & Zhang, F. (2021). ‘Effect of four viscous soluble dietary fibers on the physicochemical, structural properties, and in vitro digestibility of rice starch: A comparison study’. Food Chemistry, 357, 130181. DOI: 10.1016/j.foodchem.2021.130181 PubMed
